Your side of the computer repair experts

1, the revised label can not always save, press save on a warning dialog box appears, click OK after the software shut down.
Cause: The user changes directly on the label changes when the error operation caused.
Solution: modifications in the correct way to modify the changes that you want to modify the contents of the double-click in the original layout of the dialog box to modify the time to write, do not allow the above changes directly in the label. This changes after the return to normal.

2, the printer does not normally take the paper, only went half-sheets, after printing a solid red (Zebra plant)
Cause: The printer parameter setting error.
Solution: The Z4M machine as an example. Click on Start Menu m> Set m> Printers m> Select Z4M machines m> right-click m> attribute m> printing preferences m> Document Optionm> Dispense Modem> select Tear Off to OK the .
3, the printer print all the lights flashing and can not test the paper (Zebra plant)
Cause: The sensor fault.
Solution: clean the sensor surface dust or replace sensor.
4, the printer will print a small label in place, and print the contents of partial or total up down side
Cause: The label is too small, the sensor sensing the paper is difficult.
Solution: General tab high for at least 10 or more should we do more than position, or we need to be offset on the label set. During label settings, the label’s high set a 5mm taller than the actual label around, and then in accordance with specific migration situation on the label offset set.
5, when legible printing, bar code is not clear
Cause: The bar code is too big, the density is too small.
Solution: reduce or increase the content of bar code bar code density. 200dpi and 300dpi for the machine, the bar code density is generally more than that in 7mils scale factor to 2 or 2 above, print out the bar code was clear.
6, print label, overall print some words do not come out
Cause: The print head is dirty, wrong layout.
Solution: Clean the print head; another time to see whether the layout of the printed word to overlap, and re-layout.
7, when the printer always appear in print without paper or not ribbon (TEC-572)
Reason: not to run out of paper or ribbon; send operation command caused the error.
Solution: Check whether the right under the paper or ribbon; parameters of the machine to be fine, and then printing software to print the correct layout settings.
8, print to print is not clear, ribbon off. (105Se/SL)
Cause: The printer ribbon shaft failure.
Solution: the machine shaft ribbon pull too tight, adjust the printer ribbon shaft under tension.
9, the new file can be printed correctly, but the old file is not open, can not print.
Cause: network printing, permissions error.
Solution: Print the time to see whether the network has opened the file, if opened, must first turn off to the other computer open. And then detected under the network permission issues.
10, print the contents of print incomplete.
Cause: The print version of the software and driver is too low.
Solution: Install the new version of the software and drivers.
11, the software can not be typeset.
Cause: The software installed without a good or a computer problem.
Solution: reinstall the software, if still does not work, it may be a computer virus, please virus. Is not, please reinstall the operating system.
12, shortly after the machine at boot, three lights on the off, can not print.
Cause: The printer capacitor bad.
Solution: Replace the capacitor.
13, print process, print out the contents of the samples with the actual content of different sizes.
Cause: The print driver error.
Solution: Select the correct printer driver.
14, during a black line in the next. (Argox1000 +)
Cause: The print head did not adjust well.
Solution: adjust the print head in front of the screw.
15, machine does not switch back to Rao (TEC-572)
Cause: Set error.
Solution: adjusted the printer settings back to the various settings Rao device, if not, may be the motherboard problem, need repair.
16, printing paper often jump phenomenon
Cause: The print setting error.
Solution: Set the paper size and spacing are correct circumstances, the BMP to PCX format print format for printing.
17, take the paper machine process, the issue of abnormal sound
Cause: The machine or the machine memory is not clear teeth * bad.
Solution: remove the machine’s memory or to change gear *.
18, in the printing process, always show ribbon exhausted
Cause: The machine PCB-F or PCB-G bad
Solution: replace the PCB-F or replacement of PCB-G.
19, during thermal printing, the first stop of the rotating shaft, and display ribbon exhausted.
Reason: bad machine PCB-G

You can leave a response, or trackback from your own site.